Modified on: Thu, Aug 12, 2021 at 4:03 PM
You’re Keypad should Look like this:
TABLE OF CONTENTS
Wait for a solid green light on the keypad and system ready. Enter your code followed by the O N /O FF key.
Enter your code followed by the O N /O FF key.
Note: If your code does not work the first time or if you enter the wrong code, press the R ESET key, then re- enter your code.
Enter your code followed by the O N /O FF key to silence the siren and disarm the system. Then press the
R ESET key to erase the alarm history display.
Press the B YPASS key and then the zone # you want to bypass (2 digits, i.e. Zone 2 is 02, zone 11 is 11) then enter your code followed by the O N /O FF key. The zones will go back to normal when you disarm the system.
Chime mode will sound a tone at the keypad when the programmed zone is faulted while disarmed. Enter the Function Menu by pressing the F UNCTION key (you may have to enter your user code before pressing the F UNCTION key). Skip functions until “Activate Chime” is displayed (press NO (the I NSTANT key) until the “Activate Chime” function is displayed. When the “Activate Chime” function is displayed - press YES (the I NTERIOR key). To return to normal keypad operation, press the R ESET key. NOTE: The chime mode is disabled while armed.
Press the I NTERIOR key, and then enter your code and the O N /O FF key.
Press I NSTANT key, and then enter your code followed by the O N /O FF key.
This allows you to walk around inside, but if any door/window is open, the alarm will immediately sound.
If you have more than one area, and have the “Manager’s Mode” programmed, you can arm any area from one keypad by pressing the numerical key representing the area number, press the [*] button, then O N /O FF . In effect you will now be in that area. Enter your code, then press O N /O FF to arm/disarm that area (code must be valid in that area). If no buttons on the keypad are pressed, the keypad will automatically revert to the programmed area after 20 minutes.
To sound siren and have police dispatched immediately, press P and * at the same time. To reset after sending a panic, enter your code followed by the O N /O FF key, enter your code again followed by the O N /O FF key.
If forced to disarm the system by an assailant, enter 66 then your code followed by the O N /O FF key. This will
disarm the system, but will send a silent alarm to the central station monitoring facility and the police will be dispatched immediately.
Note : For panic and ambush codes, the central station monitoring will not call the premise before dispatching the police. If you need to cancel either of these alarms you must call the central station with your account number and password immediately.
Press reset to clear trouble. If this does not work, enter your code and press the function key until the reset menu comes up. Press the O N /O FF key. When "reset system trouble" appears, press O N /O FF again, and then press the R ESET key until screen is normal.
Power Failure - Is there a general power outage? If not:
Check power transformer (black square box plugged into outlet near panel) Check for blown fuse or circuit breaker
Battery below 11 volts – Usually due to AC power failure or Alarm
Will automatically recharge after AC power restore
If not recharged within 24 hours, it needs to be replaced
Unsuccessful communication to central station – Is phone line working?
If not: Notify your phone carrier of the problem
If so: Call the monitoring company
Give them your account number and password
Ask them to put your system on test
Trip your panic alarm (see directions above)
If this does not clear the trouble, call for service
Wireless transmitter low battery (NN = receiver number)
Call the monitoring company
Give them your account number and password
Ask them to put your system on test
Remove the transmitter cover and replace battery
Key fob low battery (NN = key fob transmitter number)
Call the monitoring company
Give them your account number and password
Ask them to put your system on test
Remove the key fob cover and replace battery
Trouble condition on a Fire Zone
Press the R ESET button to silence the sounder.
Correct the trouble, and then press the R ESET button again.
ANY OTHER MESSAGES: CALL FOR SERVICE
IF YOUR KEYPAD LOOKS LIKE THIS.
Here is how to change alarm codes.
Enter your code, then press the [FUNCTION] button. (this will put you in the FUNCTION Mode.
Press the [INSTANT] button until the screen says "ACTIVATE PROGRAM"
Press [ON/OFF] button. The screen will display the following: U01 XXX - - (U= user, X=represents code)
Use the [FUNCTION] button to move the cursor to the User Number
Enter a User number as a two digit number (users 01 - 09)
Enter a new User Code using the number buttons. If an old code is displayed, simply program over it. (To erase the digit at the cursor, press the [*] button then the [0] button.
Press the [ON/OFF] button to save code.
Repeat above steps for each new code.
Press [RESET] to end.
IF YOUR KEYPAD LOOKS LIKE THIS.
Here is how to change alarm codes.
Enter your code, then press the [FUNCTION] button. (this will put you in the FUNCTION Mode.
Press the [INSTANT] button until the number 17 in the screen. The display will scroll the following (P, 4 digits representing the software version and then UP for User Program
Use the [FUNCTION] button to move the cursor to the User Number
Enter a User number as a two digit number (users 01 - 09)
Set the cursor to the user code with the [FUNCTION] button.
Enter a new User Code using the number buttons. If an old code is displayed, simply program over it. (To erase the digit at the cursor, press the [*] button then the [0] button.
Press the [ON/OFF] button to save code.
Repeat above steps for each new code.
Press [RESET] to end.
Did you find it helpful? Yes No
